How to avoid air lock problems in your shower Pump System

The showering pump system should be efficient to provide a good pressure and give comfortable showering. However, airlocks in the pump or the pipes hinder water flow, and can be very inconvenient causing a lot of performance issues. As for the problems with water pressure, Dublin Shower Pumps supplies professional solutions to these problems. In this Blog let me explain what are the causes for Airlock, what it does, and how we can avoid it.

Understanding Airlocks in Shower Pump Systems

Airlocks are usually caused by air being locked either in the water pipes or in the air pump so that water cannot pass through regularly. As shower pumps are designed for water supply, even a tiny leakage of air can interrupt the work of the pump.

 

What Causes Airlocks?

• Incorrect Installation: If it is poorly positioned to the shower pump or pipes then it has areas where air can build up.
• Low Water Levels: If the water tank supplying the pump runs low, air can be drawn into the system.
• Sudden Water Supply Interruptions: Sudden changes in water supply, for instance during repairs, the air enters into the pipes and the pump system.
• Improper Priming: If, after the installation or maintenance, the proper priming has not been carried out, then air will be locked inside.

How airlocks affect your shower pump.

• Reduced Water Pressure: Airlocks prevent water to flow evenly or with low pressure – an issue of which shower pump installation was supposed to solve.
• Pump Damage: If operations continue with airlocks, it will heat up the pump and cause  mechanical wear.
• Noisy Operation: The air present in the system causes sounds like rattling or gurgling when the pump is on.
• Increased Energy Use: An airlocked pump needs to work harder to provide the adequate water pressure and therefore requires more energy.

How to Prevent Airlocks in Your Shower Pump System

To avoid potential problems with your shower pump, you need to take measures. Here are expert tips from Dublin Shower Pumps:

1. Ensure Proper Installation

The most important aspect of using a shower pump is installation.

• Correct Positioning: Make sure that the pump is installed  at the correct level from the source of water. For positive head pumps, the position of the water tank should be above the pump level. Negative head pumps, on the other hand, prove most suitable where the water tank is at a level with, or below, the pump.
• Angle the Pipes Appropriately: It is recommended to put the pipes at a slight angle that will make it hard for air spaces to develop. Avoid sharp or horizontal curves so that the air can’t be trapped in them.

2. Regular System Maintenance

Regular checks help to identify any complications likely to occur, allowing for proactive action to be done on them before there is a major outbreak.

• Inspect the Pump and Pipes: Check for any damage or leaks where the air can penetrate into the shower pump system.
• Clean the Filters: Clogged filters reduce the water pressure and may increase the chances of airlocks in the system. Regularly clean or replace the filters.
• Check Water Levels: Sufficient water supply in the tank must be maintained to avoid the air entering into the pipes.

3. Use Automatic Air Vents

Automatic air vents are one of the dependable methods of eliminating air from the system.

• Install Air Vent Valves: They are valves which allow the trapped air to escape as water moves through the pipe system. Place them at high areas in the piping that you expect air to accumulate.
• Consider Pressure Relief Valves: Besides air vents it is also important to use pressure relief valves to regulate the system and minimize the air-related problems.

4. Prime the Pump Correctly

Pump priming makes certain that there is no standing air inside the pump after its assembly or when in the process of repair.

• Fill the Pump with Water: Before starting the pump, manually fill it with water to expel any air.
• Follow Manufacturer Guidelines: Always follow the important instructions provided with the manufacture guidelines to prevent the risk of airlock in the pumps.

5. Upgrade to a High-Quality Pump

The upgraded high quality pumps will prevent the airlocks. 

• Choose Trusted Brands: Dublin Shower Pumps provide clients with an efficient shower with different pumps, quiet and energy-saving showers which solve water pressure-related issues.
• Consider Pump Features: Look for the features that have in-built air extraction mechanisms which eliminate the trapped air.

Troubleshooting Airlocks in Your Shower Pump System

Nevertheless, sometimes, airlocks can develop. Here’s how to deal with them effectively:

• Turn Off the Power: In order to avoid any damage or even injury do not operate the pump while attempting to make repairs.
• Manually Release Air: Open the nearest taps to let out air. In case of severe airlocks, slightly loosen the pipe connections to let the air out then secure the connection tightly.
• Flush the System: Turn on the water at a high flow rate so as to help push the air out of the system. This is particularly useful in minor airlocks.
• Call a Professional: If the problem continues, Dublin Shower Pumps can assist in identifying and solving the problem to give your system the necessary fix.

 

Dublin Shower Pumps’ Services: Features and Advantages

Dublin Shower Pumps provides quality shower plumbing services to Dublin homes incorporating skilled workmanship and reliable products. Because of our specialized knowledge of shower pump installation, clients get a consistent water flow and no stress.

 

Conclusion

Avoiding airlocks in your shower pump system will help you avoid fluctuating pressure levels and the eventual breakdown of your pump. To help you avoid common shower pump problems, it is imperative to install it correctly, perform routine checks, and you decide to invest in the excellent Shower Pumps from Dublin.

To obtain professional advice or to find out exactly the right pump services for your needs, call Dublin Shower Pumps now.

---